自上料攪拌車設計合理，結構緊湊，操作靈活，維修方便，可以一天24小時運轉，生產能力高，成本低。下面來講講自上料攪拌車離合器活塞密封性的檢測。

The self feeding mixer has reasonable design, compact structure, flexible operation, convenient maintenance, can operate 24 hours a day, high production capacity and low cost. Next, we will talk about the sealing test of the clutch piston of the charging mixer.

自上料攪拌車行走無力或油溫過高時，就需要判斷是離合器活塞密封不嚴還是油壓不足引起的，但常規檢測手段有時很難斷定是哪個原因引起故障，尤其是在無動力的情況下，檢查組裝好的變速器總成的各密封環就更困難了，此時，可采用氣壓閥進行測試。

Since the feeding mixer truck is unable to move or the oil temperature is too high, it is necessary to judge whether the clutch piston seal is not tight or the oil pressure is insufficient. However, it is sometimes difficult to determine the cause of the fault by conventional detection methods. Especially when there is no power, it is more difficult to check the seal rings of the assembled transmission assembly. At this time, the pneumatic valve can be used for testing.

將自動上料攪拌車變速器控制閥拆掉(對組裝好的變速器應在裝控制閥之前)，然后依次給變速器各油孔通人0.6一0.8MPa的氣體，若某一個孔通人氣體時，聽到“嘭“的一聲且無漏氣聲或漏氣聲很小進口計量泵，則說明與之對應的離合器活塞與缸筒間的密封良好，若聽不到活塞壓緊摩擦片的聲響且漏氣聲較大，則說明離合器活塞與缸筒間的密封失效，應更換密封件。

Dismantle the control valve of the transmission of the automatic feeding mixer (before installing the control valve for the assembled transmission), and then fill each oil hole of the transmission with 0.6-0.8MPa gas in turn. If one hole is filled with gas, When the sound of "bang" is heard and there is no air leakage or the air leakage is very small, it means that the seal between the corresponding clutch piston and the cylinder barrel is good. If the sound of piston pressing the friction plate is not heard and the air leakage is loud, it means that the seal between the clutch piston and the cylinder barrel is ineffective, and the seals should be replaced.

工作時的注意事項：

Precautions during operation:

1.在冬季施工過程中，應做以下工作：開始前檢查是否結冰；關閉工作時，小心地除去攪拌桶和供水系統中的殘留水，關閉水泵開關，并將控制手柄置于“停止”位置。

1. During winter construction, the following work shall be done: check whether there is ice before starting; When closing the operation, carefully remove the residual water in the mixing bucket and water supply system, turn off the water pump switch, and place the control handle at the "stop" position.

2.當自上料攪拌車卸貨時，如果發現水蒸發了并且坍落度太低而無法滿足用戶的要求，則可以向桶中適當加水，然后以10-14r/min的速度旋轉卸載前先旋轉30圈，以使混合充分攪拌。

2. When unloading from the charging mixer truck, if it is found that the water has evaporated and the slump is too low to meet the user's requirements, water can be properly added to the barrel, and then rotate at a speed of 10-14r/min for 30 turns before unloading to fully mix the mixture.

3.在自上料攪拌車的空載運行過程中，不得停止攪拌桶，以免在滾道和支撐輥之間產生局部顛簸，這可能對支撐滾子和滾道造成異常損壞。

3. During the no-load operation of the self loading mixer truck, the mixing drum shall not be stopped to avoid local turbulence between the raceway and the support roller, which may cause abnormal damage to the support roller and raceway.

此外在冬季停放時，水箱和供水系統中應沒有剩余水，以防止凍結和破裂。更多相關設備的使用注意事項就來我們網站//wwcoms.com.cn咨詢了解吧！

In addition, when parking in winter, there should be no residual water in the water tank and water supply system to prevent freezing and cracking. More precautions for the use of related equipment can be found on our website //wwcoms.com.cn Ask and understand!