自上料攪拌車的使用過程難免會有一些問題產生，比如說漏油問題，為了預防我們可以從6個方面來做措施：

There will inevitably be some problems during the use of the self feeding mixer, such as oil leakage. In order to prevent oil leakage, we can take measures from six aspects:

1.重視襯墊作用，車輛的零件之間的襯墊是有防漏密封作用的，那如果這些材料在質量上或安裝工藝上不符合技術要求，那就起不到密封防漏的作用，甚至會發生事故，比如油底殼或氣門罩蓋，由于接觸面積大而不易壓實，就會造成漏油。

1. Pay attention to the function of gaskets. The gaskets between vehicle parts have the function of leak proof sealing. If these materials do not meet the technical requirements in terms of quality or installation process, they will not play the role of leak proof sealing, or even cause accidents. For example, the oil pan or valve cover is not easy to compact due to large contact area, which will lead to oil leakage.

2.自上料攪拌車上的各個螺母要按規定扭矩擰緊，過松壓不緊襯墊會滲漏，過緊會使螺孔周圍金屬凸起或將絲扣寧滑而引起漏油。還有就是如果油底殼螺塞未擰緊或脫落，就很容易造成機油流失。

2. Each nut on the feeding mixer truck shall be tightened according to the specified torque. If it is too loose or not tight, the gasket will leak. If it is too tight, the metal around the screw hole will bulge or the screw thread will slide, causing oil leakage. Also, if the oil pan plug is not tightened or falls off, it is easy to cause oil loss.

3.要及時更換失效的油封，自上料攪拌車隨著使用年限的加長，車上很多部位都要注意，有些油封使用時間長了就會因老化而失去彈性，就很可能因此產生漏油現象。

3. The failed oil seals should be replaced in time. As the service life of the self loading mixer increases, many parts of the vehicle should pay attention to. Some oil seals will lose their elasticity due to aging after a long service life, which may lead to oil leakage.

4.避免單向閥、通氣閥堵死。由此引起箱殼內溫度升高，油氣充滿整個空間，排放不出去，是箱殼內壓力升高潤滑油消耗增加和更換周期縮短。發動機通氣系統堵塞后，增加了活塞的運動阻力，使油耗增加。由于箱殼內外氣壓差的作用，往往會引起密封薄弱處漏油。因此需要對車輛進行定期檢查、疏通、清洗。

4. Avoid blocking of one-way valve and vent valve. As a result, the temperature in the case increases, the oil and gas fill the whole space, and can not be discharged. The pressure in the case increases, the consumption of lubricating oil increases, and the replacement cycle shortens. After the engine ventilation system is blocked, the movement resistance of the piston is increased and the fuel consumption is increased. Due to the effect of the air pressure difference between the inside and outside of the casing, oil leakage often occurs at the weak sealing position. Therefore, regular inspection, dredging and cleaning of vehicles are required.

5.妥善解決各類油管接頭的密封，對于車輛上經常拆裝的螺母要經常檢查，發現問題要及時更換。

5. Properly solve the sealing of various oil pipe joints, regularly check the nuts that are often disassembled on the vehicle, and timely replace them if problems are found.

6.避免輪轂甩油。輪轂軸承及腔內潤滑油脂過多，或其油封裝配不妥，質量不良或老化失效，制動頻繁引起的輪轂溫度過高；車軸螺母松動等都會引起輪轂甩油。因此潤滑要適量。

6. Avoid hub oil throwing. Too much lubricating grease is found in the wheel hub bearing and cavity, or the oil package is not properly matched, the quality is poor, or aging is invalid, and the wheel hub temperature is too high due to frequent braking; Loose axle nuts, etc. will cause hub oil throwing. Therefore, proper lubrication is required.

自上料攪拌車預防漏油的六大措施就講解到這里了，您對此有什么事項就來我們網站//wwcoms.com.cn咨詢吧！

This is the end of the six measures to prevent oil leakage of the loading mixer. If you have any questions, please come to our website //wwcoms.com.cn Consult!