小型攪拌機是比較常用的設備，它將各種原材料按科學配比加水攪拌均勻，為生產優良磚坯提供的前提條件，我們接下來詳細分析下小型攪拌機的結構及各部分的功能。

Small mixer is a commonly used equipment. It will add water to mix various raw materials in a scientific proportion, providing a prerequisite for the production of excellent brick. Next, we will analyze the structure and functions of each part of the small mixer in detail.

1、攪拌缸

1. Mixing cylinder

它是由厚鋼片制成“奧米加”形狀，而且由特別管狀架框承托，這能保證更佳的屈服阻力，端板承托的法蘭亦能使缸身得到堅硬及使軸心不偏不歪。缸身亦十分安全，方便使人進入，其上可根據客戶要求裝攪拌監察器。門框裝有密封橡膠條，可完全防塵。

It is made of thick steel sheets in the shape of "Omega" and supported by special tubular frame, which can ensure better yield resistance. The flange supported by the end plate can also make the cylinder body hard and the shaft center not deflected. The cylinder body is also very safe and convenient for people to enter. The mixing monitor can be installed on it according to customer requirements. The door frame is equipped with a sealing rubber strip, which can completely prevent dust.

2、缸內裝有襯板

2. Liner plate is installed in the cylinder

缸內是由件件可螺釘鎖緊及互相替換的組件所砌成。它們都是防磨損高鉻耐磨合金鑄鐵制成，其硬度達HRC54.襯板的使用壽命可達40000罐次。生產過程中要及時調整葉片與襯板的間隙(<5mm)，否則會加劇葉片、襯板的磨損。

The cylinder is made of components that can be locked and replaced by screws. They are made of wear resistant high chromium wear-resistant alloy cast iron, and their hardness reaches HRC54. The service life of the lining plate can reach 40000 cans. During the production process, the clearance between the blade and the lining plate shall be adjusted in time (<5mm), otherwise the wear of the blade and lining plate will be aggravated.

3、攪拌臂

3. Mixing arm

攪拌臂由優良合金鋼制成，配合得當的拌臂位置可保證達到均勻好的效果。

The mixing arm is made of excellent alloy steel, and the proper mixing arm position can ensure a uniform and good effect.

4、攪拌葉片

4. Mixing blade

葉片是經過科學分析，反復試驗而終確定的更佳形狀、尺寸、角度以及兩軸距，在攪拌過程中保證了攪拌臂、葉片使物料充分地在縱向和橫向和上下產生劇烈地搓揉、流動，在短的時間內達到物料均勻拌和之目的。

The blade is a better shape, size, angle and two wheelbase finally determined through scientific analysis and repeated tests. During the mixing process, the mixing arm and blade ensure that the materials can fully rub and flow violently in the longitudinal and transverse directions and up and down, and achieve the goal of uniform mixing of materials in a short time.

5、卸料

5. Unloading

氣缸可操作卸料的運行，共分三個停放的位置，包括關，半開及全開，這能立即地把混凝土卸落攪拌輸送中。當按下開閘的按鈕時，相應的電磁閥便會動作，然后電機轉動，料門關閉。由于氣缸活塞密封圈的磨損，氣缸便會抵消沖程的加速，必要時檢查更換密封圈。

The air cylinder can operate the unloading operation, which is divided into three parking positions, including off, half open and full open, which can immediately unload the concrete during mixing and transportation. When the brake opening button is pressed, the corresponding solenoid valve will act, then the motor will rotate and the material door will close. Due to the wear of the cylinder piston seal ring, the cylinder will offset the acceleration of the stroke. If necessary, check and replace the seal ring.

6、軸的密封

6. Sealing of shaft

由于黃膠密封及軸端會磨損及損壞，因此泥漿將會滲漏，在這種情況下需要調整或更換軸端密封件此機仍可繼續操作(軸承分隔及遠離密封)。

The yellow glue seal and shaft end will be worn and damaged, so the mud will leak. In this case, it is necessary to adjust or replace the shaft end seal. The machine can still continue to operate (bearing separation and away from the seal).

7、減速機

7. Reducer

電機與減速機之間的動力傳送，是靠“V”形三角皮帶帶動實現的。同心動力的連接，可使軸同步地旋轉。

The power transmission between the motor and the reducer is driven by a V-shaped V-belt. The connection of concentric power can make the shaft rotate synchronously.

8、攪拌系統

8. Mixing system

攪拌形式是靠兩水平軸以相反方向轉動而成的，在兩軸之上，設有相同數量的拌臂，并作螺旋狀排列。拌臂的特別形狀，它們起交錯地旋轉，如此的攪動，在短時間內，能保證有好的品質效果，因為在不同重量或體積下，它能避免分隔地聚集而成不平均狀態。

The mixing form is formed by rotating two horizontal shafts in opposite directions. The same number of mixing arms are arranged on the two shafts in a spiral manner. The special shape of the mixing arm. They rotate alternately. Such agitation can ensure a good quality effect in a short time, because under different weights or volumes, it can avoid the uneven state caused by the separated aggregation.

通過以上介紹，我們可以清晰的了解小型攪拌機是如何工作的，它對原材料的處理起著關鍵性的作用，更多相關內容就來我們網站//wwcoms.com.cn進行咨詢吧！

Through the above introduction, we can clearly understand how the small mixer works. It plays a key role in the processing of raw materials. More relevant information can be found on our website //wwcoms.com.cn Consult!