小型混凝土攪拌機在正常的投料攪拌過程中，攪拌主機出現悶機跳閘現象原因分享及故障處理方法如下：

During the normal feeding and mixing process of small concrete mixer, the reason sharing and troubleshooting methods for the trip of the mixing machine are as follows:

1、原因1·投料過多，引起小型混凝土攪拌機負荷過大

1. Cause 1. Excessive feeding causes excessive load of small concrete mixer

這個要檢查整個稱料系統是否正常，小型混凝土攪拌機內是否有上盤殘余物料以及有無二次投料現象；

This is to check whether the whole weighing system is normal, whether there is any hanging wall residual material in the small concrete mixer and whether there is any secondary feeding phenomenon;

2、原因2·攪拌系統葉片與襯板之間的間隙過大，攪拌過程中，增大了阻力

2. Cause 2. The gap between the blade and the lining plate of the mixing system is too large, which increases the resistance during the mixing process

檢查小型混凝土攪拌機葉片與襯板之間的間隙是否在3~8mm；2、襯板厚度是否＞2-3mm，如果襯板厚度不達標，則要及時更換襯板。

Check whether the clearance between the blade and the lining plate of the small concrete mixer is 3-8mm; 2. Whether the thickness of lining plate is ＞ 2-3mm. If the thickness of lining plate is not up to the standard, replace the lining plate in time.

3、原因3·傳動皮帶太松，使傳動系統效率低

3. Cause 3: The transmission belt is too loose, which makes the efficiency of the transmission system low

檢查傳動皮帶的松緊程度是否超過20mm，如是則調整或更換

Check whether the tightness of the drive belt exceeds 20mm. If yes, adjust or replace it

4、原因4·攪拌主機上蓋安全檢修開關被振松，引起停機

4. Cause 4. The safety maintenance switch on the upper cover of the mixing host was loosened, causing the shutdown

檢查主機上蓋安全開關是否松動并處理

Check whether the safety switch on the upper cover of the host is loose and handle it

5、原因5·減速箱及菊花軸損壞，檢查更換即可

5. Cause 5. The reducer and chrysanthemum shaft are damaged. Check and replace them

應當及時進行補救措施。可以對控制臺電流表進行監控；對襯板和攪拌機刀片之間的距離進行檢查，查看是否超過5厘米。當三角皮帶出現老化現象時，應當在及時進行更換，與此同時，還應當檢查主軸和聯動軸之間是否固定。

Remedial measures should be taken in a timely manner. It can monitor the console ammeter; Check the distance between the lining plate and the mixer blade to see if it is more than 5cm. When the V-belt is aged, it should be replaced in time. At the same time, check whether the main shaft and the linkage shaft are fixed.

對攪拌機的配料系統進行多方位檢查，確保未超標情況以及二次投料，對傳感器進行檢查，使其能夠正常運作。在運行攪拌機之前，還應當對主機上蓋進行檢查，查看是否有松動或者損壞情況。如果有，則應當及時進行更換。關注我們//wwcoms.com.cn，了解更多相關事項！

The batching system of the mixer shall be inspected in multiple aspects to ensure that it does not exceed the standard and the second feeding. The sensors shall be inspected to ensure that it can operate normally. Before running the mixer, check the upper cover of the main machine to see if it is loose or damaged. If any, it shall be replaced in time. Follow us //wwcoms.com.cn , learn more about it!